FS Industries ENGINEERED STEEL PRODUCTS
Priced Full Line Products Catalog
20 Technology Way West Greenwich, RI 02817
Toll free:(800) 421-0314 • In RI:(401) 272-4570 • Fax:(401) 421-5679
Home Order Search Quote Contact Us About Us My Account Shopping Cart
Back to Product Category

CONCRETE SQUARE 4 SEAT TABLE


Order Online, by Phone, or by E-Mail

~ Add items to your online shopping cart ~
Click the Model No. of the item you wish to purchase.


MODEL TF3120
concrete square 4 seat table Simple lines and colors make these tables
an excellent choice for an outdoor café or
park area. High quality, low maintenance.
Accepts umbrella, without extra stand.
Assembly required. Also available in
ADA version as well as 2 seat version.
ALSO--REFINISHING KIT: TF3315
Make your table look NEW!! All the
materials you need to refinish your concrete
tables, benches, and seats to restore them
to like new condition.
Size: 64" Sq. x 30" H installed
Weight: 1100 lbs.
Seating Capacity: 8 persons
Material: Reinforced concrete
Reinforcing: 1/4” & 3/8" Dia. steel rebar
MODEL: TF3120
REFINISHING KIT:TF3315
PRICE: $1,900.00
PRICE: $198.50
Hardware: (1) - table-to-leg bracket Anchoring: (4) - 3/8" x 1-1/2" inserts
    (angle-brackets not provided)
Standard: (1) - 1-9/16" Dia. x 2" pop-out
     plug in table top for umbrella pole
Assembly: Do not over tighten bolts or
     inserts will pull out.
Maintenance: Periodically rinse with
      water and mild detergent. Reseal
      annually.
Packaging: Packaged unassembled in
     crate, and shrink wrapped in plastic.
(8) - seat-to-leg brackets
(8) - 3/8" Dia. x 5 1/2" hex screws
(8) - 3/8" locking hex nuts.
(16) - 3/8” x 7/8” O.D S/S F/W
(4) - Neoprene Pads
(24) - 3/8" Dia. x 1-1/4" hex flange screws
(1) - 1/8” x 3” Keeper Pin
Frame (legs): (1) - top interlocking leg
(1) - bottom interlocking leg
Top: (1) - top 36" Sq. x 2"
Benches: (2) - benches 36" L x 12" W x 2" H

Available Colors

Refinishing Ground & Polished Concrete Instructions
Kit Includes:
- 2 lbs Grout Mixture
- 10 oz Bonding Agent
- 4 Spray Cans of Sealer
Additional Items Needed:
- Rubber Gloves
- #240 Sand Paper
- Sanding Block
- Mixing Tool
- Scrubbing Pad
- #80 Grit Sand Paper
- Pail
- Sponge
- Squeegee
Note: Wear rubber gloves during entire refinishing process. Refinishing results are best
when all excess grout is removed and surface is sanded smooth. Check for and clean up
spills after each step. Newly refinished tables will retain an attractive appearance for
several years if they are resealed at least once a year.

1. Scrub and Rinse
Rinse surface with water while using scrubbing pad to
remove dirt and grime. Using the sanding block and
#80 sand paper, sand surface. Repeat rinse.
2. Grout
Mix grout and bonding agent together to create
a creamy consistency in a pail. Allow to set for
5 minutes Apply to the surface using a circular
motion, with a sponge to fill all voids. Can
be used on smooth edges, not on acid wash
surfaces.
Note: Acid wash edges to be taped off before groutin
the surface to avoid getting grout in pores of edge.
3. Remove Excess Grout
Immediately remove all excess grout with a squeegee.
Apply water as needed to keep grout moist with a spray
bottle. Thoroughly inspect the surface to be certain it is
clean. Allow to cure for approximately 24 hours.
4. Wet-Sand
Once the surface has cured, wet-sand grouted
surface using sanding block, #240 sandpaper
and water.
5. Clean
Thoroughly rinse with water and allow to dry. Surface
must be dust free. If tape was needed for edges
remove tape before cleaning the surface.
4. Wet-Sand
Once the surface has cured, wet-sand grouted
surface using sanding block, #240 sandpaper
and water.

SPECIFICATION
1.1 SUMMARY
  A. Section includes: Furnish Precast Concrete Table
       indicated on drawings or specified herein.
1.2 REFERENCES
  A. American Society for Testing & Materials
      1. ASTM C33     2. ASTM C150     3. ASTM C31
1.6 QUALITY ASSURANCE
  A. Qualifications of Manufacturer: Manufacturer
        to be pre-qualified by specifier prior to
        bidding. Failure to comply will result in
        disqualification of bid. Manufacturer to have
        at least five years experience in the manufacturer
        of precast concrete tables field proven for at
        least five years.
1.5 SUBMITTALS
  A. Submit product data, shop drawings and
       Samples.
      1. Product Data: Manufacturer's specifications
          and technical data edited specifically for
          proposed system, including the following
          specific information:
         a. Detailed specification of construction
             fabrication.
         b. Manufacturer's installation instructions
         c. Maintenance literature
         d. Product warranty
      2. Shop Drawings: Indicate pertinent dimensions,
          general construction, component connections
          anchoring methods, hardware and installation
          procedures.
      3. Samples as requested by Architect.
1.10 WARRANTY
    Manufacturer shall submit a written warranty for
    precast products for the period of two years upon
    acceptance of products.
2.2 MATERIALS
  A. Portland Cement: ASTM C150 specifications
       for Portland Cement.
  B. Aggregates: All aggregates to meet ASTM C33
      specifications, to be cleaned of foreign matter
      and properly graded to size.
  C. Coloring: Pigments used shall be inorganic,
        resistant to alkalinity and used as per
        manufacturers recommendations.


Concrete Square Table, Picnic Tables, Concrete Tables, Park Furnishings, Tables, Site Amenities, Site Furnishings, and
Street Furniture from your source for material handling equipment.
Back to Product Category
Visa - MasterCard - AMEX
Home - Order - Search - Quote - Contact Us - About Us - My Account - Shopping Cart