 |
ENGINEERED
STEEL PRODUCTS |
| Priced
Full Line Products Catalog |
20
Technology Way • West Greenwich, RI 02817
Toll free:(800) 421-0314 • In RI:(401) 272-4570 • Fax:(401)
421-5679 |
|
|
|
|
Back
to Product Category
|
|
 |
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click the Model No. of the item you wish
to purchase. |
|
|
 |
|
|
|
|
|
Inground
Mount Bola Metal Bike Rack |
|
|
|
|
|
|
Metal
powder coat inground mount bola bike rack.
Holds one or two bikes.
Size: 26"
x 38"
Unit Weight: 20 lbs
Material: Metal
Anchoring: Inground anchoring required. |
|
|
|
|
|
Model: MF9021
Price: $349.20 |
|
|
|
|
|
|
 |
|
Technical
Data - Innoteck Powder Coatings |
|
General
Description
A functionalized polyethylene copolymer based thermoplastic powder coating
designed for maximum mechanical
performance, impact resistance and UV-stability. Polyarmor® G17 Texture
is a non-skid protective coating.
Surface Preparation
Chemical Pretreatment - Multi-stage
phosphate conversion coating may be used
Mechanical Preparation- (SSPC-SP6)
2-3 mil (50-75µm) anchor profile using clean, sharp edged blast media
NOTE: Properly preparing parts before powder coating is essential for
a quality finish. This includes cleaning,
rinsing, drying and insuring the substrate surface is free and clear of
any contaminates.
Fluidized Bed
For fluidized-bed dipping, preheat parts to
450° F (230°C) adjusting for part thickness. Dip parts in fluidized-bed
of Polyarmor® G17 Texture for 8-10 seconds.
Allow excess powder to stand for 1 minute then carefully blow off
the excess material. Post bake coated part @380°
F - 400° F (193 - 205°C) for 3 – 4 minutes.
Important:Polyarmor® G17 Texture
is designed to texture on the HORIZONTAL surface of the part. There
will
be slight texturing on vertical surfaces. For best
results, do not water quench cool Polyarmor® G17 Texture.
Electrostatic Deposition
Polyarmor® G17T can be applied via electrostatic
deposition with or without pre-heat. When not using pre-heat,
the powder should be applied to achieve a thickness
of 8 – 10mils (203 - 254µm). Recommended voltage setting
when using Corona equipment is 40 – 60 kv.
Post-baking at 350 - 425°F (175 - 220°C) for 5 to 10 minutes
depending on metal thickness, or until desired
flow out is achieved. For preheated parts, the recommended preheat
temperature is 400°F (205°C). Deposit Polyarmor®
G17 8-12mils (203 – 300µm) or higher if desired. For
improved surface finish, parts may be post-baked
for a short period of time if necessary. Times and temperatures in
the oven will depend on configuration and
thickness of the part.
No Cure Time
Thermoplastic powder coatings need only be
heated enough to flow out the coating, nothing more. Overheating
may cause degradation or embrittlement of
the coating. Coating may be put into service when cooled. |
|
Powder
Properties |
Coverage
(100% efficiency) |
25.65
ft² per pound @ 8mils (5.24 m² per kg @ 203µm) |
Particle
Size
| Available
in fluid bed & spray grades
|
VOC
Content |
ZERO |
Thickness
(Recommended) |
8
- 30mils (203 – 762µm) |
Storage
Stability |
Store
in dry area below 90 F, keep container closed with liners sealed
and out of direct sunlight and any moisture or external contaminates.
Always use good manufacturing practices. |
Performance
Properties |
Melting
Point
| |
221°F
(105°C) |
Specific
Gravity |
ASTM
D 792 |
0.95g/cm3 |
Adhesion |
ASTM
D 4541 |
800psi
(5.6MPa) |
Impact
Resistance |
ASTM
B 2794 |
>320
in-lbs (35.8 Joules) |
Vicat
Softening Point |
ASTM
D 1525 |
162°F
(72°C) |
Tensile
Strength |
ASTM
D 638 |
3482psi
(12MPa) |
Elongation
(%)
| ASTM
D 638 |
13% |
Humidity
Resistance |
ASTM
D 2247 |
No
blistering or loss of gloss after 1000 hours |
Salt
Spray |
ASTM
B 117 |
2,000
hrs. no significant change in color
or gloss |
QUV |
ASTM
G 53 |
2,000
hrs. no significant change in color
or gloss |
Taber
Abrasion
| ASTM
D 4060 |
26mg
loss, CS 17 wheel, 100mg loss, CS 17
wheel |
Flexibility
(Conical Mandrel Bend) |
ASTM
D 522 |
1/8in
(3.2mm), no cracks (>32%) |
Gloss |
ASTM
D 523 |
12 |
Melt
Index |
ASTM
D 1238 |
20 |
|
|
The
Seller renders all technical advice, recommendations and services gratis.
They are based on technical data which
the Seller believes to be reliable, and are intended for use by persons
having skill and know-how at their own
discretion and risk. Seller assumes no responsibility for results obtained
or damages incurred from their use by Buyer
in whole or in part. Such recommendations, technical advice or services
are not to be taken as a license to operate
under or intended to suggest infringement of any existing patent. |
|
|
Loop Bike Racks, Metal Bike
Racks, Circle Metal Bike Rack, Park your Bike, Circular Design, Meal-Armor
Surface Mount
Loop Bike Rack, Mounted Loop Bike Rack, Circular Bike Rack and Metal Loop
Bike Rack from your source for material
handling equipment. |
Back
to Product Category |
 |
|
