![](../../../../images/catalog/shim.gif)
![FS Industries](../../../../images/catalog/fsindustries.gif) |
ENGINEERED
STEEL PRODUCTS |
Priced
Full Line Products Catalog |
20
Technology Way West Greenwich, RI 02817
Toll free:(800) 421-0314 In RI:(401) 272-4570 Fax:(401)
421-5679 |
![](../../../../images/catalog/shim.gif) |
|
![](../../../../images/catalog/shim.gif) |
Back
to Product Category
WHEEL
TROLLEY FESTOON SYSTEMS |
|
![](images/top_fc_ws4.jpg) |
|
SEE BELOW
FOR INSTALLATION INSTRUCTION FOR WIRE SUPPORTED SYSTEMS |
|
|
![](images/model_no_click_yellow.gif) |
|
Order
Online, by Phone, or by E-Mail |
|
|
|
~ Add
items to your online shopping cart ~
Click the Model No. of the item you wish
to purchase. |
|
|
PRICES |
System
Model # |
Max.
Working Travel-Feet |
No.
of Trolleys (FC-TR4) Required |
Prices |
|
20 |
1 |
$170.00 |
|
30 |
3 |
$242.00 |
|
40 |
5 |
$315.00 |
|
50 |
7 |
$389.00 |
|
60 |
9 |
$462.00 |
|
|
Each
wheel trolley system includes the parts in the following table. Order cable
and connectors separately. |
Index
# |
Model
# |
Component |
1 |
FC-CS4 |
End
Clamp Assembly |
2 |
FC-SRCE2 |
Eye
Bolt and Thimble |
3 |
FC-SRCC2 |
U-Clamp,
4 required |
4 |
FC-TR4 |
Single
Wheel Trolley |
5 |
FC-SRC2 |
Nylon
Coated Wire Rope, 1/4" dia. |
6 |
FC-TB5 |
Two-Wheel
Lead Trolley |
7 |
FC-TB4 |
Tow
Arm Assembly |
|
|
FC-WS4 |
|
|
|
|
|
|
|
![](images/fc_ws4.jpg) |
|
|
|
|
|
FC-TR5 |
|
FC-SRCE2 |
|
|
![](images/fc_tr5.jpg) |
|
![](images/fc-srce2.jpg) |
|
|
|
|
FC-CS4 |
|
|
|
|
|
|
![](images/fc_cs4.jpg) |
|
|
|
|
|
FC-TB4 |
|
|
![](images/fc_tb4.jpg) |
|
|
|
|
|
|
|
|
|
|
|
INSTALLATION
INSTRUCTIONS FOR WIRE SUPPORTED SYSTEMS |
|
Figure
1 illustrates a typical stretched wire supported festoon cable system. Component
part numbers for all types of
the wire supported systems are listed below. |
|
![](images/note_fc_ws4.jpg) |
|
Index
# |
Model
# |
Component |
Index
# |
Model
# |
Component |
1 |
FC-CS4 |
End
Clamp Assembly |
5 |
FS-SRC2 |
Nylon
Coated Wire Rope, 1/4" dia. |
2 |
FC-SRCE2 |
Eye
Bolt and Thimble |
6 |
FS-TR5 |
Two-Wheel
Lead Trolley |
3 |
FC-SRCC2 |
U-Clamp,
4 required |
7 |
FC-TB4 |
Tow
Arm Assembly |
4 |
FC-TR4 |
Single
Wheel Trolley |
|
|
|
Note
that the support brackets which are normally mounted on each end of the
crane bridge to be electrified are not
included in the system but are supplied by the purchaser. These brackets
must be adequate to support the cable tension
applied when the adjustment is made to eliminate the cable sag caused by
the weight of the trolleys and festoon cable.
Normally this will be 1/4" thick angle or channel iron adequately fastened. |
|
The
position of the cable on the bridge is determined by the placement of the
tow arm assembly. The tow arm must
located just under the cable to provide for pushing back on the trolleys
when returning to the storage end of the system.
Be sure that a suitable place is found to install the tow arm and then place
the cable just above the tow arm. It will be
necessary to drill a hole in each support bracket for the 3/8" eye
bolts which will hold the cable ends. |
|
At
the end nearest the junction box where the cable connection is to be made,
install the FC-CS4 end clamp assembly.
(R-CS4A for round cable) The end clamp assembly has an eye bolt for one
end of the support cable. Feed the trolleys
onto the support cable and tie them near the end clamp until it is time
for a running test. Install the FC-SRCE2 eye bolt
and thimble at the opposite end. Draw the 1/4" nylon coated cable through
the eye bolt at each end and clamp the end
of the cable loop with the FC-SRCC2 U-clamps (2 at each end). Tighten the
nuts on the U-clamps to 50 inch-pounds. |
|
Adjust
the outside tightening nut on each of the eye bolts until adequate tension
is applied. To test for adequate tension,
first run the trolleys to the storage end so they are not weighting on the
cable. At the center of the system pull down on
the cable. If you can pull down more than 1" on a 20 to 60 ft. cable,
keep tightening until it does not exceed that amount.
The breaking strength of 1/4" nylon covered cable is 4,200#. Then tighten
the inside locking nut on the eye bolts at
each end of the system. |
|
Untie
the trolleys and feed the festoon cable through the saddles until the proper
amount for trolley spacing on the
system is achieved. Tighten the saddle bolts to hold the cable(s) in place
and then run the system back and forth to
see that all trolleys run freely. |
|
Then
apply power to the system and check through several cycles at slow speed
to check under operating conditions. |
|
Wheel Trolley Festoon Systems,
Wire Supported Systems, Slide Wire Systems, Industrial Festooning Systems,
Festoon Cable
Systems, Pendant Control, Duct-O-Wire, Flat Cable, Flat Cables, and C-Track
from your complete source for material handling
equipment. |
Back
to Product Category |
![Visa - MasterCard - AMEX](../../../../images/catalog/cards.gif) |
|